Comments on: Kwikee Step Repair

By: Dick

Dick — Fri, 22 Aug 2008 23:58:27 +0000

I removed the four prong plug because of corrosion and wired it direct. I don’t know what I did because the step extends when I close the door and retracts when I open it. I was pretty impressed with myself when the steps worked but that only lasted until I discovered they worked backwords.

By: ken

ken — Fri, 25 Jul 2008 15:53:47 +0000

I had a new chassis battery installed in my 99 dolphin. The step was open and stayed opened, will not close since installing the battery. I have located the 5amp fuse, but keep blowing it when i install. The fuse is in the same compartment as the converter on a board with many more fuses. The step will move when i install the fuse but blow the fuse instanly an the step comes back out. Can anyone help? EMAIL ME AT rdbug57@aol.com thanks

By: john

john — Wed, 23 Jul 2008 22:16:38 +0000

my 2 step on a 2004 winnebago oprates fine except in the ign override mode. the 15 amp fuse blows after a few cycles. i have tried a 25 amp justy to check and the fusse blows too. any suggestions?

By: Erick

Erick — Tue, 01 Jul 2008 02:01:06 +0000

Have 2 step Kwikee, leaving for Lake George tomorrow, this am steps went down and before stoping in the full down position, retracted 2 inches, and kept going back and forth, any ideas?

By: Allen

Allen — Sun, 29 Jun 2008 18:20:20 +0000

I have a two step system.. It’s been acting up so I checked the door switch. The steps work sometimes, not others. I checked voltage and I’m only getting 10v to the switch (tested from the controller with ground). 12v at the understep light. Any ideas?

By: kwikee

kwikee — Fri, 27 Jun 2008 16:04:25 +0000

[...] I mention below is no longer available- kwikee changed the motor enough that it is not possible …http://rx4rv.com/archives/11Kwikee Systems?2007. MultiAd, Inc. All Rights Reserved. Terms &ampamp Conditions [...]

By: Rod Van Assche

Rod Van Assche — Wed, 25 Jun 2008 15:32:43 +0000

I have a 91 Fleetwood Bounder by stairs quit so on the advice of Kwikee I was told to replace my controler #9513 with the newer #9506 controler this required new door switch install I have installed all the new parts I have power to the red wire, the white wire none to the yellow (override ) wire and the brown is hooked to the door sensor With the motor hooke directly to a battery it works properly in and out but with the motor hooked to the controler I can get no movement either way ( I do have the stairs unhooked pin removed) for this testing I have installed a jumper on the door switch Still no movement. Where do i go next?

By: Bill

Bill — Thu, 19 Jun 2008 22:55:46 +0000

I have a 23 series kwikee step assembly. The gear box that the motor bolts to is broken. Does anyone know where I can get just the gearbox? I’ve looked up different websites and can only fine a new assmebly with motor. My motor works fine. Any help is greatly appreciated.

By: Mark LaMonica

Mark LaMonica — Sun, 01 Jun 2008 16:45:17 +0000

On my 03′ HR, my 3 step Kwikee steps seem to have striped gears by just hearing the motor
run with no rotation.
I took the steps off and removed the motor assembly. Is there anywhere I can fine the
inside drive gear, not the worm (its fine). Everyone wants to sell me the whole
motor assembly.
Its does to seem obvious just by reading I should have been oiling my moving hedges.
Thanks

By: Tim

Tim — Mon, 19 May 2008 14:37:33 +0000

Sure glad I found this site. The last time my steps stuck down
I was working and didn’t have time to investigate. Fixed it this
time after reading this. I will definetly pay more attention to
lube after this. Thanks again. Tim